Project Jeep CJ-7 – Restoring the Jeep CJ-7 Tub – Part One
Goals for the Jeep CJ-7 body:
Rust Removal
Repair of sheet metal
Repair of body mounts
Preparation for painting
As the restoration begins it happened to start right about the time we moved into a new house with an attached garage that had no electrical outlets or lighting. Not even a single shelf. So the garage required some modifications that were all centered around optimizing the space for working and storing the CJ-7. This included shelves in all the available spaces, shop lights (still need more), a heavy duty work bench, electrical service with outlets in all the right places (needs more of them too), and get rid of all the junk. Once that was completed the grinder hit the tub.
Inside the tub much of the steel had been replaced with heavier gauge galvanized steel sheet metal by the previous owner leaving much of my work just to finish up the job. Underneath required removal of the excess old floor steel which was cut back to the welds. The cutting went pretty smooth and quick. Measurements were taken and new rail are being fabricated where they were rotted away and will be welded in. Also I began cutting stock steel to fortify the body mounts and add some steel where it could use it for extra strength.
These body mounts were cut off to make way for newly fabricated rails.
The budget Rebuild by Ralph HasselThe complete build is documentedhere on www.Offroaders.comThis 1978 Jeep CJ-7 never started life as a complete Jeep; rather it was built completely from parts. The goal was to build a […]
A Budgeted Jeep CJ-7 Rebuild from Concept to Conception by Ralph Hassel My evolution of thought… It all started with a humbling realization a number of years ago. My current vehicle, a 92 Toyota pickup 4×4, […]
This relatively simply oil pan modification, though it’s being done on Project CJ-7, can be installed on almost ANY 4×4 with an exposed oil pan. Though it may be a rare event to poke a […]
This Project CJ-7 article is about converting and armoring a Dana 300 skid plate to work with a Dana 20 transfer case. An ounce of prevention is worth a few pounds of steel. After hearing stories […]
In swapping the T-18A onto this Jeep project, a good tip was passed onto me from Mike of www.Jeepfan.com. This tip has to do with the stock clutch fork being used in the stock bell […]
Fabricating Custom U-Bolt Plates with Skid Protection for Project Jeep CJ-7 With the job of a Dana 44 axle swap to the project CJ-7 came the need for new u-bolt plates. Two things made stock u-bolt […]
A Simple yet very effective method of protecting your tie rod from impact with rocks and things, is to raise the tie rod up. Raising the Drag link also reduces bump-steer, a side effect of […]
Using 6 bucks worth of material to protect a 300 dollar 3-core radiator and to cool the V8 Engine. When looking at the grill of my 78 CJ-7, the one thing that just stuck out like […]
After doing some research I finally decided to look for a Borg-Warner T-18A manual transmission. Manual because that is what I prefer. The T-18A because of it’s 6.32:1 first gear and it’s heavy duty, cast […]
Project Jeep CJ-7 Daystar Swaybar Bushings Tip. When swapping out your stock CJ swaybar bushings with the Daystar Swaybar Bushings, here’s a Tip – Use the CJ bracket! Here’s why…First off, upgrading your sway bar bushings […]
Project Jeep CJ-7 – Disassembling the Scout II Dana 44 Front Axle. After acquiring the Dana 44 axles I also picked up a Dana 30 narrow track front axle that was in great shape. The […]
Continuing on from the front axle prep, the rear axle’s spring pad angle recorded and spring pads were removed. That was followed up by an inspection of differential and rear drum brakes to make sure […]
Project Jeep CJ-7 Scout II Dana 44 Axles Swap onto a CJ-7 FrameNew Custom Fabricated HangersFront Springs – Front HangersThe front hangers were a little easier to design than the rear hangers. Mainly because they […]
Project Jeep CJ-7 Scout II Dana 44 Axles Swap onto a CJ-7 FrameFabricated Leaf Spring HangersInstalling the Front Leaf Springs HangersBelow is the whole set of hangers. Gussets have been welded in and all the holes […]
Project Jeep CJ-7 U-Bolt Skid PlatesFabricating Custom U-Bolt Plates with Skid ProtectionWith the job of a Dana 44 axle swap to the project CJ-7, came the need for new u-bolt plates. Two things made stock […]
Detroit – Good news for 2011-2013 Jeep JK Wrangler owners plagued by the left-cylinder head cracking issue. Chrysler Group has extended the 5-year/100,000 mile warranty out to 10-years/150,000 miles on the left-cylinder head for customers […]
If Jeeps, Jeeps and more Jeeps are your thing, you won’t want to miss this years All Breeds Jeep Show presented by PA Jeeps! July 19th and 20th 2014 This year’s 19th annual event will be […]
These body mounts were cut off to make way for newly fabricated rails. 
