Project Jeep CJ-7 – Disassembling the Scout II Dana 44 Front Axle.
After acquiring the Dana 44 axles I also picked up a Dana 30 narrow track front axle that was in great shape. The goal here was to disassemble the front Dana 44, clean it up, paint it, then reassemble the 44 using the Dana 30 outer knuckles and retain some of the stock Jeep parts. This was possible due to the fact the the 44’s and the 30’s inner knuckles are the same dimensions and the axle spline count is the same. Reasons for swapping to the CJ knuckles were, better turning radius than the Scout knuckles and the availability of the parts. My Scout outer knuckles needed rebuilding and I would have had to replace most of the Scouts outer knuckle parts due to wear and tear and rust. Also the fact that the Dana 30 outers were a bolt on without modifications to the knuckles made it easy to do. The Scout outer knuckles are, in fact, bigger and stronger but I kept the parts in case I ever decide to swap it back (after rebuilding them).
The Scout II Dana 44 front axle had some very stubborn ball joints. After soaking them in penetrating oil for a few days and using heat to try to press them out I ended up cutting them with the angle grinder. They were being replaced anyway.
The stripped down front Dana 44 axle.
Donor CJ narrow track Dana 30 outer knuckles used on the Dana 44. The axles are the same spline count which makes it a simple bolt on. I decided to go this route because I liked the idea of reusing as much CJ parts as I could while using the Dana 44 housing. I still kept the Scout II outer knuckles because of their strength but if I ever decide to reuse them they will have to be overhauled.
Rear Dana 44 spring pads were removed because they would not only need to be relocated due to the width of the CJ springs but the pads themselves are for 1 7/8 inch wide springs. The BDS springs are a beefy 2 1/2 inch wide so I ordered new spring pads. The pads won’t be welded on until the drive train is in place and I can line up the pinion angle. For now they will be cleaned up and painted.
The budget Rebuild by Ralph HasselThe complete build is documentedhere on www.Offroaders.comThis 1978 Jeep CJ-7 never started life as a complete Jeep; rather it was built completely from parts. The goal was to build a […]
A Budgeted Jeep CJ-7 Rebuild from Concept to Conception by Ralph Hassel My evolution of thought… It all started with a humbling realization a number of years ago. My current vehicle, a 92 Toyota pickup 4×4, […]
This relatively simply oil pan modification, though it’s being done on Project CJ-7, can be installed on almost ANY 4×4 with an exposed oil pan. Though it may be a rare event to poke a […]
This Project CJ-7 article is about converting and armoring a Dana 300 skid plate to work with a Dana 20 transfer case. An ounce of prevention is worth a few pounds of steel. After hearing stories […]
In swapping the T-18A onto this Jeep project, a good tip was passed onto me from Mike of www.Jeepfan.com. This tip has to do with the stock clutch fork being used in the stock bell […]
Fabricating Custom U-Bolt Plates with Skid Protection for Project Jeep CJ-7 With the job of a Dana 44 axle swap to the project CJ-7 came the need for new u-bolt plates. Two things made stock u-bolt […]
A Simple yet very effective method of protecting your tie rod from impact with rocks and things, is to raise the tie rod up. Raising the Drag link also reduces bump-steer, a side effect of […]
Using 6 bucks worth of material to protect a 300 dollar 3-core radiator and to cool the V8 Engine. When looking at the grill of my 78 CJ-7, the one thing that just stuck out like […]
After doing some research I finally decided to look for a Borg-Warner T-18A manual transmission. Manual because that is what I prefer. The T-18A because of it’s 6.32:1 first gear and it’s heavy duty, cast […]
Project Jeep CJ-7 Daystar Swaybar Bushings Tip. When swapping out your stock CJ swaybar bushings with the Daystar Swaybar Bushings, here’s a Tip – Use the CJ bracket! Here’s why…First off, upgrading your sway bar bushings […]
Project Jeep CJ-7 – Disassembling the Scout II Dana 44 Front Axle. After acquiring the Dana 44 axles I also picked up a Dana 30 narrow track front axle that was in great shape. The […]
Continuing on from the front axle prep, the rear axle’s spring pad angle recorded and spring pads were removed. That was followed up by an inspection of differential and rear drum brakes to make sure […]
Project Jeep CJ-7 Scout II Dana 44 Axles Swap onto a CJ-7 FrameNew Custom Fabricated HangersFront Springs – Front HangersThe front hangers were a little easier to design than the rear hangers. Mainly because they […]
Project Jeep CJ-7 Scout II Dana 44 Axles Swap onto a CJ-7 FrameFabricated Leaf Spring HangersInstalling the Front Leaf Springs HangersBelow is the whole set of hangers. Gussets have been welded in and all the holes […]
Project Jeep CJ-7 U-Bolt Skid PlatesFabricating Custom U-Bolt Plates with Skid ProtectionWith the job of a Dana 44 axle swap to the project CJ-7, came the need for new u-bolt plates. Two things made stock […]
Sometimes the creativity of certain people is astounding. Have a walk around look at this 1953 Jeep Willys Overland 8×8 that went up for sale several years ago. Custom fabricated by renouned fabricator Dick Cook […]
If you’re like me and you’ve owned many offroad vehicles over the years, you’re probably equipped your latest offroader acquisition with hand-me-downs from the previous generation 4×4’s. For me I’m either trying to save money […]
A number of years ago, I got the Jeep bug. I even know when and where I was when the bug hit me. I preparing to build something for the offroad, maybe a Toyota FJ-40 or […]
3 Comments
Inquiring on steering linkage used and set up. I used a D44 out of a scout and my D30 knuckles. The tie rod hits up against diff cover. Hoping you have a solution. Thanks
Hey Ralph,
What are you using for tie rod/drag link. I saw you flipped them but did you upgrade to heavy duty units? If so which ones did you use. I just picked up a CJ7 with a front/rear scout dana 44’s but stock tie rod/drag link and I want to upgrade.
thanks!
The only real solution for the Scout’s zero degree castor is to cut the welds off and pound the knuckle off. Then press it back on at the correct rotation of negative castor.
Inquiring on steering linkage used and set up. I used a D44 out of a scout and my D30 knuckles. The tie rod hits up against diff cover. Hoping you have a solution. Thanks
Hey Ralph,
What are you using for tie rod/drag link. I saw you flipped them but did you upgrade to heavy duty units? If so which ones did you use. I just picked up a CJ7 with a front/rear scout dana 44’s but stock tie rod/drag link and I want to upgrade.
thanks!
The only real solution for the Scout’s zero degree castor is to cut the welds off and pound the knuckle off. Then press it back on at the correct rotation of negative castor.